Floor Plan/Reflected Ceiling Plan Display (Stair Settings)

Each Stair has two groups of settings, defining display preferences for the Stair Symbol (and its components) on Floor Plan and on Reflected Ceiling Plan.

Note: Switch the Stair’s display by view, using Model View Options. See Stair Symbol: Choose Floor Plan Display or Reflected Ceiling Plan.

FPDStairsOverview.png 

Related Topics:

Stair Display Layouts (Show on Stories)

Choose the stories on which the Stair’s 2D symbol should be displayed.

Layout On (Stair Display On Each Story)

Vary a stair’s symbol display, story by story.

Stair Settings: Symbol Components

Show or hide each symbol component of the Stair. (Overrides the show/hide definitions at Model View options.)

Stair Settings: Symbol Overrides

Apply overrides to the display of the Stair’s entire 2D symbol (lines, pens, fills).

Set Attributes for Each Stair Symbol Component

Set attributes and choose symbol type for any Symbol component (e.g. Break Mark, Walking Line, Numbering).

Stair Display Layouts (Show on Stories)

Use the pop-up to define the Stories on which the Stair’s 2D symbol should be displayed.

FPDStairLayout.png 

The stories you define (for example, “All Relevant & One Story Up”) are listed in the field below (under “Layout On”).

Relevant Story

A Relevant Story is one which the Stair physically intersects. When defining Stories for Stair display, multistory Stairs can have, for example:

RelevantMiddleStories.png 

a Relevant Bottom Story

one or more Relevant Middle Stories

a Relevant Top Story

Layout On (Stair Display On Each Story)

Under Layout On: Click on each Story name, then choose how to display the Stair on that story:

Break Mark: With or without a Break Mark

Visible vs. Hidden Attributes: To use either Visible or Hidden attributes on the displayed parts of the Stair. The set of attributes (for hidden and visible parts) is defined for each symbol component on its own settings page. See below.

StairFPLayoutOptions.png 

Use the Preview to get an idea of the Stair’s 2D display on each story.

Note: If the Stair has an associated Railing, you can apply these same Display settings to the Railing: Use the checkbox in Railing Settings (see Railing Display Layouts (Show on Stories).)

Stair Layout Examples

GroundFloorLayoutSettings.png 

GroundFloorLayout.png 

Stair Layout on Ground Floor: With Break Mark, Use Visible Line Type (Below) and Hidden Line Type (Above)

FirstFloorLayoutSettings.png 

FirstFloorLayout.png 

Stair Layout on First Floor: No Break Mark, Use Visible Line Type

Additional Layouts are available for multistory Stairs, with multiple Break Marks.

See also Relevant Story.

On a given Story, you can just display the part between Break Marks.

InBetweenVisible.png 

Stair Layout on Middle Stories: Display Between Break Marks Only

NoneVisibleHidden.png 

Stair Layout on Middle Stories: None (below Break Line1) - Visible (Between Break Lines)
- Hidden (Above Break Line 2)

Stair Settings: Symbol Components

These controls are available for both the Floor Plan Display node and the Reflected Ceiling Plan Display node of Stair Settings.

Symbol Components: By Model View Options

Check this to show/hide the Stair’s 2D components as defined at Document > Model View > Model View Options.

See Show/Hide Stair Symbol Components (by Model View Options).

StairFPsymbol.png 

Symbol Components: Customize in Stair Settings

Uncheck “by Model View Options” and use the list below to specify which symbols to show or hide. The Grid and Break Mark cannot be hidden.

For example: If you have both an existing and a new Stair in the same view, you may prefer to display the existing one with less detail.

Select that Stair, open its Settings, and uncheck By Model View Options.

From the list below, uncheck the items (e.g. Description, Numbering) that you don’t need to see on that Stair.

StairFPShowHide.png 

Note: This Stair, for which you customized the visibility of its Symbol components, will always appear as you set it, regardless of the current Model View Options setting!

Stair Settings: Symbol Overrides

Available for both the Floor Plan Display node and the Reflected Ceiling Plan Display node of Stair Settings. These settings are independent of Model View Options.

Use them to optionally apply overrides to the display of the Stair’s entire 2D symbol (lines, pens, fills).

To apply a Line/Pen/Fill override: Check the respective Override box, then select an attribute from the controls below.

StairFPOverrides.png 

Set Attributes for Each Stair Symbol Component

Available for both the Floor Plan Display node and the Reflected Ceiling Plan Display node of Stair Settings. These settings are independent of Model View Options.

To set attributes, choose a Symbol component (Break Mark, Walking Line, etc.) from the Stair Settings tree structure, to access its settings.

For each Symbol Component:

Choose a Component type from the pop-up menu

Set the Component’s attributes in the bottom panel - separately for the Visible and Hidden parts of the symbol, as applicable.

See also Visible Parts and Hidden Parts.

View the Preview to get an idea of how the component will look.

StairComponentFP.png 

Structure Component Settings

Use these controls to set the 2D display of Stair Structures (Flight and Landing), depending on the Structure type you are using.

Note: Stair Structure components are selected on the Structure node of Stair Settings. See Flight and Landing Structures.

Attributes vary for the structure’s Visible and Hidden parts.

Break Mark Symbol

Choose a Break Mark Symbol (e.g. Zigzag)

Set Break Mark position by Height or at a particular Riser number

Set Break Mark angle (to Vertical/Horizontal, or define the number of goings that it should span)

Apply an optional extension to the Break Mark lines

Set Break Mark attributes (Break Mark Component Settings), including the width of the “Motif” (e.g. zigzag) if any

BreakMarkSettings.png 

You can edit the Break Mark symbol graphically, after selecting it in Edit mode (Symbol view).

See also Edit Break Mark Symbol.

Walking Line Symbol: Position and Display Settings

The Walking Line Symbol Position refers to the Symbol, whose position you can edit manually, either here or in Edit mode.

(In contrast, the Calculated Walking Line, defined in the Geometry and Positioning panel of Stair Settings, affects Tread geometry, and can be edited in Stair Settings only. See Offset Walking Line on Turning (Winder with Equal Goings).

In the Display Settings shown here:

“Default” setting means that the Walking Line Symbol is at the same location as the Calculated Walking Line, defined in Stair Settings - Geometry and Positioning panel

“Center” places the Walking Line Symbol at the center of the Stair

“Custom” means that the Walking Line has been edited graphically to a new position

For details on Symbol editing, see Edit Stair Symbol Components Graphically.

WalkingLineCustom.png 

Walking Line End Symbol: End at Second to Last Tread

Check this option to end the Walking Line at the tread before the last one.

WalkingLineSecondTread.png 

Walking Line End Symbol: Edit Arrow Width/Height

When choosing an End symbol for the Walking Line, note that the “automatic” options mean that the arrow endpoints are fixed, to exactly one Going width.

To edit arrow endpoints, choose a Custom symbol type. You can edit the arrow graphically, too, in Edit mode.

WalkingLineCustomArrow.png 

See also Edit Walking Line Arrow and Edit Walking Line Symbol Position.

Numbering Symbol: Show Numbers on Stories

Use these controls to set the Numbering preferences for the Stair, including story-dependent display, as needed.

Numbering: Choose Risers or Treads.

Placement: Choose which Treads/Risers should be numbered.

Other options let you define where to begin and/or end the Numbering, or to restart Numbering at Landings.

NumberingSymbol.png 

You can edit (move or rotate) the numbers graphically, after selecting them in Edit mode (Symbol view).

See Edit Stair Numbering Items.

You can also use special Stair Labels to number Treads and Risers: See Labeling Stairs.