2D Members (Slab, Wall, Roof)

Slabs, Walls, and Single-plane Roofs are represented as 2D Members in the Structural Analytical Model.

2D Members are plane surfaces generated along the center of the element’s core plane. The 2D Member has at least four nodes and one surface area connecting them.

The analytical Member does not extend outside of the physical body unless it has been adjusted.

Customize 2D Member color at Structural Analytical Model Representation (Preferences).

2DMembersWall.png 

Which Elements Are 2D Members of the Structural Analytical Model?

Slabs, Walls, and Roofs will generate a 2D Member in the Structural Analytical Model if they meet these conditions:

Load-bearing

Contains a core

“Structural Member” checkbox is activated in Element Settings

Geometry is supported (see table below)

Element Type

Geometry

Member of Structural Analytical Model?

Slab

all

YES

Wall

Straight

YES

 

Curved

YES

 

Slanted (straight)

YES

Double Slanted

NO

Trapezoid

NO

Slanted, Double Slanted (curved)

NO

Complex Profile

YES

Polygon Wall

NO

Roof

Single-Plane

YES

Multi-Plane

NO

Tool Settings for 2D Members

Use the Structural Analytical Parameters panel of Slab, Wall or Roof settings.

SAM2DSetting.png 

Structural Function - Enable Load-Bearing

Set the Structural Function to Load-Bearing. This is the same control, with the same value, as in the Structural Function control found in the Classification and Properties panel.

Structural Member - Enable for Structural Analytical Model

This box is checked by default: include this element in the Structural Analytical Model as a 2D Member.

Notes: 

Available only if Structural Function is set to Load-Bearing

If the element is a composite or Complex Profile, it must include at least one Core skin/component in order to be part of the Structural Analytical Model

Uncheck if the element should NOT be included in the Structural Analytical Model. (For example, a thin moisture-blocking membrane on an underground story.)

2D Member - Structural Behavior

The Structural Behavior setting defines the Member’s behavior in a FEM-based structural analysis program: specifically, which types of forces this element is designed to bear.

Choose an option to define the Member’s structural behavior:

StructBehavior.png 

Shell: Takes all loads

Plate: Element is able to take loads perpendicular to the plane.

Wall: Element is able to take loads along its plane.

The available definitions are fixed and cannot be customized.

The right choice here depends on the receiving structural analytical software. Some softwares will filter out incoming elements based on this Structural Behavior setting. If you find that exported 2D Members are not being imported to the receiving software, you may have to adjust their Structural Behavior definition in ARCHICAD.

The definition can be entirely independent of the tool used to create the element: a vertical Wall’s behavior can be set to “Plate” or “Shell”; a horizontal Slab’s behavior can be set to “Wall”.

European structural analytical softwares (e.g. SCIA Engineer) consider the incoming Member’s structural type. For these, “Shell” is the default.

U.S.-based softwares (e.g. RISA-3D) consider the physical model element of the 2D Member: for these, choose “Wall” as the structural behavior in Wall settings, and “Plate” in Slab or Roof settings.

The Structural Behavior setting has no effect on the Physical Model.

Allow Rule-based modifications - 2D Member

By default, all checkboxes are on:

Ignore small openings

Stretch & Cutback

Offset

This means that corresponding adjusters and opening filter, defined in the Generation Rules dialog, will affect this 2D Member element.

See Structural Analytical Model Generation Rules.

To exempt this 2D Member from adjustments: uncheck the box(es).

Custom Offset

If the Offset box is unchecked:

Redefine this element’s eccentricity along the z axis (perpendicular to the plane of the 2D Member), either graphically or by entering a value.

See Eccentricity.

Translation and Rotation

See End/Edge Releases.